» »
» » Precision gauge strips Brass sheet 2.0321
Precision gauge strips Brass sheet 2.0321
See larger image
I have seen this product cheaper elsewhere.

Precision gauge strips Brass sheet 2.0321

-CLINQ LAITON FEUIL

Composed of 63% copper and 37% zinc, this material is the standard alloy for spring-tempered, rolled brass for flat springs, connectors and stamped parts.

Quantity : 
+
-
Available Dispatched within 10 days

FORMAT-EPAISSEUR EN MM-1280

47.56€ Excluding VAT
57.07€ VAT INCLUDED
Add to quotation requests

  FORMAT
EPAISSEUR EN MMPAR 5 FEUILLES 150 X 500FEUILLE 1000 X 305
0.01057.07€ 
0.02545.84€ 
0.05051.29€18.23€
0.07556.99€ 
0.10073.16€23.15€
0.15075.56€26.23€
0.20084.89€30.82€
0.25077.63€34.02€
0.30074.99€37.49€
0.40080.77€51.06€
0.50092.76€62.95€
0.600101.82€ 
0.700128.11€ 
0.800129.90€ 
0.900143.86€ 
1.000157.56€122.52€
Facebook - Partager
LinkedIn
Viadeo
description
Notice

Material Data sheet                                                                               Issue: October 2015

 

Download file here:

https://sbc-trading.fr/images/Image/File/Precision-gauge-strips-brass-CW508L-2.0321%20.pdf

 

 

Hard-rolled brass strip, mat. no. 2.0321

 

  1. Applications:

Composed of 63% copper and 37% zinc, this material is the standard alloy for spring-tempered, rolled brass for flat springs, connectors and stamped parts.

For deep-drawn parts the brass should be used in a softer condition like F30 with a tensile strength of about 300 N/mm².

 

Further applications:

pieces for electrical engineering and precision mechanics This material is not magnetic.

2.  Material codes:

German Norm:             2.0321, CuZn37 AISI:

ASTM:                           C 27200

Engl. Norm:                  CW508L

AFNOR:                        -

Japan. Norm:               -

 

3.  Chemical composition: *

Cu:                                 62-65.5 %

Zn:                                 balance

Ni:                                  max. 0.30 %

Pb:                                 max. 0.10%

Fe:                                 max. 0.10 %

Sn:                                 max. 0.10 %

Al:                                  max. 0.05 %

Other:                            max. 0.10 %

* the exact composition of each batch can be documented by a material certificate

2.2 or 3.1 according to DIN EN 10 204.

 

4.  Delivery condition:

Condition:                     temper rolled, not hardenable

Surface:                        no data available

Flatness:                       according to EN-Norms

Ultimate tensile str.:    370-650 N/mm² (depending on the thickness) Further mechanical data: see chapter 7 and 8.

5.  Sizes:

Thicknesses:                0.01 – 1.0mm

Standard sizes:           150 + 305mm (not in all thicknesses) Edges:          cut

Lenghts:                        individual lengths from 5 to 10 000mm or as coil

 

The following sizes are available from stock (without obligation), status: October 2015:

 

Thickness in mm

Width in mm

Tensile strength in N/mm²

Annotation

0.01

150

550-640

 

0.020

150

>630

 

0.025

150

550-640

 

0.03

150

>630

 

0.04

150

>630

 

0,05

150 + 305

>630

 

0.075

150

550-640

 

0.10

150 + 305

>450

 

0.15

150 + 305

480-560

 

0.20

150 + 305

550-640

 

0.25

150 + 305

480-560

 

0.30

150 + 305

550-640

 

0.40

150 + 305

550-640

 

0.50

150 + 305

550.640

 

0.60

150

>630

 

0.70

150

370-440

Only in the low tensile strength on stock!

0.80

150

550-640

 

0.90

150

550-640

 

1.00

150 + 305

540-610

 

 

6.  Tolerances:

Thickness tolerance: T3

Width tolerance:          DIN EN 1791 Straightness:      normal

Flatness:                       DIN EN 1791

 

7.  Further mechanical data:

Yield str. Rp0,2 :         depending on the tensile strength ElongationA 80:           depending on the tensile strength

 

If good tumbling is done, the following values can be achieved: Reversed bending stress (Mean stress = 0):

The maximum value is approx. 1/3 of the tensile strength for brass if bending direction is at a 90° angle to the rolling direction

 

Fluctuating bending stress (Minimum stress = 0):

no data available, but the maximum value is lower than for the reversed bending stress.

 

As the fatigue strength depends on different factors like the corrosive conditions and the edge treatment, no definitive endurance limit values can be guaranteed.

At high forces or bending not in the right angle to the rolling direction the alloy CuBe2 is recommended (or hardened steels like 1.1274 or 1.4031Mo).

 

8.  Physical properties

Density:                                 8.44 g/cm³

Thermal conductivity:          120 W/(m °C) depending on the temperature

 

Spec. heat capacity:           377 J/(kg °C) mean value at 50 – 100 °C Thermalexpansion:        20.2 x 10 -6 (between 30 - 100 °C) Electric resistance:       15µOhm cm

Modus of elasticity:             110 000 MPa at 20 °C Relativepermeability µr:         brass is non magnetisable

 

9.  Blanking

We recommend a punch-to-die clearance of 4-10 % of the strip thickness.

The corner radius should be at least 0.25 mm and the punching die should be at least twice the strip thickness.

The pieces should then be tumbled to receive a good edge roundness.

 

10.  Laser cutting

This alloy can be laser cut by solid state lasers.

 

11.  Photo etching

The alloy 2.0321 can be etched easily.

 

12.  Bending

As this material is supplied in the temper rolled condition, the rolling direction is important regarding the bending. The suggested minimum bending radius depends on the tensile strength of the material.

 

Bending at right angle (90°) to the rolling direction:

 

410-490

480-560

550-640

>630 N/mm²

Up to 0,50 mm

ca. 0,5 x t

ca. 0,75 x t

ca. 1,0 x t

ca. 2,0 x t

0,50-1,00 mm

No data available

No data available

No data available

No data available

t = strip thickness

 

Bending parallel to the rolling direction:

 

410-490

480-560

550-640

>630 N/mm²

Up to 0,50 mm

ca. 0,5 x t

ca. 0,5 x t

ca. 2,0 x t

ca. 6,0 x t

0,50-1,00 mm

No data available

No data available

No data available

No data available

t = strip thickness

 

13.  Flat grinding

Brass is not magnetic and can not be hold by magnetic clamping devices of flat grinding machines.

 

14.  Welding

Brass is not suitable for welding due to a low evaporating temperature of zinc at 906°C. Hard and soft soldering can be done easily.

 

15.  Corrosion resistance

Brass has a good resistance against most organic fluids, water and water steam and different salt solutions, but at high chloride contents a corrosion due to “dezincification” can occur.

 

Important Annotation

The specifications which are given in this technical information sheet about the condition and application of the alloys are only for reference and are no confirmation about certain performances and characteristics.

 

The information correspond to our own experiences and experiences of our suppliers.

We can not guarantee for the results during processing and utilisation.

 

Back to top
description
Notice

Reviews about this Precision gauge strips Brass sheet 2.0321 (0 reviews)

There is no review for this item, add the first one.
[Add your review]
Back to top